we check the OpRegion version and use the rvda pointer when available.
from 2.1 the pointer is relative.
Change-Id: I64d8aea65368aa3c5597f63a2b96b6a430e04315
Reviewed-on: https://review.haiku-os.org/c/haiku/+/5109
Reviewed-by: Jérôme Duval <[email protected]>
Tested-by: Commit checker robot <[email protected]>
as it's possible they use the audio class_sub instead of hd_audio.
* also power up the audio function, this seems required on Jasper Lake.
* tested on Acer Swift 1 SF114-34.
Change-Id: I603018b1b973e7884aa99a58be1c24e568f2d5ae
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4928
Reviewed-by: waddlesplash <[email protected]>
Tested-by: Commit checker robot <[email protected]>
* init works better with this. it doesn't work yet, but at least the boot
isn't completely borked.
* also fix the infinite loop in SoftwareReset() to timeout after 100ms.
Change-Id: I76dac8360eaf3575adf7d0b3bf3e2b72daeedb21
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4923
Reviewed-by: waddlesplash <[email protected]>
check that the correct BIOS is found with the device and PCI ids.
make the allocated rom area bigger like Linux, otherwise page faults occur.
Change-Id: Iae6ff1c8dfd81ea16c20e73d511f9a0a96f9b071
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4844
Reviewed-by: Alex von Gluck IV <[email protected]>
the socket interface module checks the receive.low_water_mark to automatically
notify a read event. available_data will be zero, thus enabling the notification.
fixes the test poll_nm in NSPR.
Change-Id: I5354faec439df96671506550cdb144a45f6082b1
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4820
Reviewed-by: waddlesplash <[email protected]>
LGTM seems to provide GCC 9.2, for which the flag -Wformat-diag is falsely
detected as supported.
Change-Id: I95a5946d9c6cd2af73e85070973f855fba3fcc39
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4786
Reviewed-by: Jérôme Duval <[email protected]>
If a thread executes a system call and meanwhile a different thread calls another one, then
the ongoing call is marked as unfinished. When the call returns it will be marked as resumed.
* remove PreSyscall, now unused.
Change-Id: Iea45b866be2c40568d766c2ed3cc73e34b9d1293
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4765
Reviewed-by: waddlesplash <[email protected]>
in the case of poll(), the events should be printed before the actual syscall,
and the revents after, while taking in account the return value.
thus B_DEBUGGER_MESSAGE_PRE_SYSCALL needs to be enabled and handled.
the attribute "preSyscall" is added to identify such syscalls, and the parameters
are identified with the attribute "inOut".
Change-Id: I390643ea176c720738c5ec4fc75a3a4c7125a3cd
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4763
Tested-by: Commit checker robot <[email protected]>
Reviewed-by: waddlesplash <[email protected]>
on x86, gcc emits a local reference to __stack_chk_fail_local
which can only be provided by a static library. as we don't have
a libroot_nonshared, we use libgcc from gcc, in which libssp_nonshared
was merged, from version 8.3.0_2019_05_24-11.
Change-Id: I22bf26dec5c1fe69a3915a923bd716a494f846ce
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4564
Reviewed-by: Jérôme Duval <[email protected]>
these colorspaces are packed as RGB or RGBA, not BGR or BGRA.
RGB48_BIG and RGBA64 only differ in the endianess of the channel the 2-byte value.
this is a big difference with RGB24_BIG and RGBA32_BIG, in which case _BIG
means the order is RGB (BGR) and not BGR (BGRA).
BGR48, BGRA64 could indeed be added, if needed.
I chose 0x11 and 0x12 arbitrarily, but given the order of channels 0x1011
and 0x1012 might make more sense. This would mean using another bit for "real"
bigendian colorspaces.
Only the color conversion to 32-bits is implemented.
Tested with the RAWTranslator modified to output 16bpp with success.
Found some references in enum AVPixelFormat in libavutil/pixfmt.h.
Change-Id: I4b023dec85d01f1e63e1b053139e5bb5d263a0e0
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4468
Tested-by: Commit checker robot <[email protected]>
Reviewed-by: Adrien Destugues <[email protected]>
alc(4): add support for Mikrotik 10/25G NIC
The new Mikrotik 10/25G NIC is mostly compatible with AR8151 hardware,
with few exceptions:
* card supports only 32bit DMA operations
* card does not support write-one-to-clear semantics for interrupt status
register
* MDIO operations can take longer to complete
This patch adds support for Mikrotik 10/25G NIC to the alc driver
while maintaining support for all earlier HW.
The patch was tested with FreeBSD main branch as of commit
f4b38c360e63a6e66245efedbd6c070f9c0aee55
This was tested on Intel i7-4790K system with Mikrotik 10/25G NIC.
This was tested on Intel i7-4790K system with RB44Ge (AR8151 based 4-port NIC)
to verify backwards compatibility.
PR: 256000
Submitted by: Gatis Peisenieks <[email protected]>
MFC after: 1 week
Change-Id: I83cdeb24caccad15a9647a72159d979ecbd647f0
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4361
Tested-by: Commit checker robot <[email protected]>
Reviewed-by: Jérôme Duval <[email protected]>
Theorically we could define __STDC_NO_THREADS__ internally in GCC, but
threads.h probably will be added in the future, and the compiler won't
notice.
Using this stdc-predef.h header and including it in GCC would solve this
nicely, and saves us from hardcoding.
The header can eventually be removed when obsolete.
Change-Id: I29aa58686e3c45449dc63e02e5a9e13a960b9090
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4097
Tested-by: Commit checker robot <[email protected]>
Reviewed-by: Adrien Destugues <[email protected]>
POSIX defines this structure but specifies only two fields (which we
already implement). However, both the *BSD and Linux have agreed on
some more fields, which are often assumed to be there by applications.
The benefice of having compatibility fields is
greater as having to patch every other software at HaikuPorts.
Change-Id: Ie28ca2e348aa16b4c57eb3498eb62175100d9b9d
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4083
Tested-by: Commit checker robot <[email protected]>
Reviewed-by: Niels Sascha Reedijk <[email protected]>
Reviewed-by: Jérôme Duval <[email protected]>
User threads aren't supposed to be able to adjust the interrupt flag (IF). A few
apps for instance DOSBox would just use the popf instruction and disable the
flag, expecting the change to be ignored.
Quote from the Intel manual:
"The interrupt flag (IF) is altered only when executing at a level at least as
privileged as the IOPL. If a POPF/POPFD instruction is executed with
insufficient privilege, an exception does not occur, but the privileged bits
do not change."
fix#14711
Change-Id: I0519312c1151a1dd76541f60283c6c210a5b21a6
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4046
Reviewed-by: Adrien Destugues <[email protected]>
the AC flag in eflags/rflags, pushed in the iframe by the CPU, is kept intact after handling the exception, since the fault handler is run with the faulted iframe and does a simple jump. The AC flag would otherwise be set until the syscall returns to userland.
Change-Id: I24f763032ab98029dd162fb411e1541586451606
Reviewed-on: https://review.haiku-os.org/c/haiku/+/4040
Reviewed-by: Adrien Destugues <[email protected]>
Tested-by: Commit checker robot <[email protected]>
This is getting more common in tablets and laptops. It replaces PS/2 for
the internal keyboard and pointing devices. This is simpler and cheaper
than using up USB ports, and also simpler than the old and quirky PS/2
protocol.
The HID spec is the same no matter what transport is used (it is also
applicable for Bluetooth). Ideally we could create a separate HID bus
manager that would handle all these devices in a generic way, but that
is a lot of work nad extra complications for uncertain gains.
For now, just move the common files to a shared directory where both
drivers can use them. As a result the files are compiled twice, which is
what we want, because currently they hardcode some device paths that
need to be different for each driver.
Change-Id: I0327f6864dd0a4372b708f7b7ecf299aa86a6ea9
Reviewed-on: https://review.haiku-os.org/c/haiku/+/2466
Reviewed-by: Adrien Destugues <[email protected]>
Tested-by: Commit checker robot <[email protected]>
654517304167bb4675aa14ada0a1dac9efe71c9b Convert to if_foreach_llmaddr() KPI.
5ab0c8434a7befeafbaf81e899fc23f660b64c9d ath(4) processing input packets in taskqueue.
6c3e93cb5a4aa4b8a2d8d4d326f2a7c34d3a4458 Use NET_TASK_INIT() and NET_GROUPTASK_INIT()
add extra ANI fields for the AR9300 HAL.
I'm trying to debug why reception upstairs here is so terrible and it
turns out ANI is buggy. (Which is no surprise, ANI is always buggy.)
Tested:
* Carambola2 (AR9331), STA/AP modes
ANI fixes and preparation for userland control.
* The ani function bitmap was being badly used when determining if a command
could be used. In hostap modes only a couple of the ANI control parameters
are enabled.
* The ani function bitmap was not being reset to HAL_ANI_ALL if transitioning
from AP -> STA.
* Change mrcCckOff to mrcCck - 1 == on, rather than 1 == off. This matches
the API used to set the value from userland via the diagnostic API.
* Handle OFDM/CCK noise immunity level commands in ar9300_ani_control().
These will only come from userland and it will go and program the rest of
the ANI control parameters with the values in the ANI table.
* Ensure all of the ANI parameters can be tweaked at runtime, even if they're
disabled.
Tested:
* carambola2 (AR9331), STA/AP modes
Fix return value check to not complain.
Compilers complain more about things, so let's keep them happy.
Extend the start PCU receive to handle resetting ANI.
One of the fun issues with scanning has been how the existing
ANI values were programmed into the hardware when channels were
changed. If you're on a really crappy channel and ANI has made
you deaf then when you scan you continue to be deaf on all channels.
This code passes in a flag to startpcureceive which in AR5416 and later
is also used to enable ANI. This allows it to know if it's a normal
operation or a scan operation.
This fixes my situation at home where a temporary spot of a device
going deaf due to interference starts scanning and .. can't hear
anything until I restart.
Now, this isn't the full fix - ideally:
(a) all the ANI config and per-channel information would be migrated
to the shared HAL stuff and enabled for all of the NICs;
(b) when a station reassociates and some other error conditions
(like missed beacons, NF calibration failures, etc) a knob
to reset ANI parameters would likely help recovery.
But hey, I'm committing bits of code again! woo!
Tested:
* AR9344 (2G), STA operation
Fix ANI calibration during non-ACTIVE states; start poking at rate control
These are some fun issues I've found with my upstairs wifi link at such a ridiculous
low signal level (like, < 5dB.)
* Add per-station tx/rx rssi statistics, in potential preparation to use that
in the RX rate control.
* Call the rate control on each received frame to let it potentially use
it as a hint for what rates to potentially use. It's a no-op right now.
* Do ANI calibration during scan as well. The ath_newstate() call was disabling the
ANI timer and only re-enabling it during transitions to _RUN. This has the
unfortunate side-effect that if ANI deafened the NIC because of interference
and it disassociated, it wouldn't be reset and the scan would never hear beacons.
The ANI configuration is stored at least globally on some HALs and per-channel
on others. Because of this a NIC reset wouldn't help; the ANI parameters would
simply be programmed back in.
Now, I have a feeling I also need to do this during AUTH/ASSOC too and maybe,
if I'm feeling clever, I need to reset the ANI parameters on a given channel
during a transition through INIT or if the VAP is destroyed/re-created.
However for now this gets me out of the immediate weeds with connectivity
upstairs (and thus I /can/ commit); I'll keep chipping away at tidying this
stuff up in subsequent commits.
Tested:
* AR9344 (Wasp), 2G STA mode
Have the final attempted rate in 11n modes to be the lowest one.
Right now ath_rate_sample has a fixed rate schedule, rather than the minstrel_ht
style "best, good, most reliable" triplet. So, if higher rates are tried then
it'll not fail back to a lower MCS rate in that transmission schedule.
This means that in low SNR situations it'll not easily drop to MCS0 unless enough
transmissions occur to allow rate control to eventually decide to drop; and if
it's TCP traffic it'll get slowed down because of packet loss.
It's worse for 2-stream and 3-stream rates; it doesn't ever fall back to lower
stream rates, and these higher stream rates required higher SNR to work.
So instead let's (for now?) have each of the 11n transmit rates use MCS0 as
the last attempt. ath_rate_sample will quickly see that rate succeeds more
and will move to it much quicker.
Testing:
* AR9344 (Wasp) - 2G STA mode
Fix queue bits a bit
Found by PVS Studio: duplicate assignment; add assignment of tqi_compBuf.
Submitted by: <[email protected]>
Differential Revision: https://reviews.freebsd.org/D20431
ath_hal: fix typo in ath_hal_printf
Fix endian macros to work in and out of kernel tree.
Yes, people shouldn't use bitfields in C for structure parsing.
If someone ever wants a cleanup task then it'd be great to remove them
from this vendor code and other places in the ar9285/ar9287 HALs.
Alas, here we are.
AH_BYTE_ORDER wasn't defined and neither were the two values it could be.
So when compiling ath_ee_print_9300 it'd default to the big endian struct
layout and get a WHOLE lot of stuff wrong.
So:
* move AH_BYTE_ORDER into ath_hal/ah.h where it can be used by everyone.
* ensure that AH_BYTE_ORDER is actually defined before using it!
This should work on both big and little endian platforms.
Add some extra data into the rate control lookup.
Right now (well, since I did this in 2011/2012) the rate control code
makes some super bad choices for 11n aggregates/rates, and it tracks
statistics even more questionably.
It's been long enough and I'm now trying to use it again daily, so let's
start by:
* telling the rate control code if it's an aggregate or not;
* being clearer about the TID - yes it can be extracted from the
ath_buf but this way it can be overridden by the caller without
changing the TID itself.
(This is for doing experiments with voice/video QoS at some point..)
* Return an optional field to limit how long the aggregate is in
microseconds. Right now the rate control code supplies a rate table
and the ath aggr form code will look at the rate table and limit
the aggregate size to 4ms at the slowest rate. Yeah, this is pretty
terrible.
* Add some more TODO comments around handling txpower, rate and
handling filtered frames status so if I continue to have spoons for
this I can go poke at it.
Extend ath_rate_sample to better handle 11n rates and aggregates.
My initial rate control code was .. suboptimal. I wanted to at least get MCS
rates sent, but it didn't do anywhere near enough to handle low signal level links
or remotely keep accurate statistics.
So, 8 years later, here's what I should've done back then.
* Firstly, I wasn't at all tracking packet sizes other than the two buckets
(250 and 1600 bytes.) So, extend it to include 4096, 8192, 16384, 32768 and
65536. I may go add 2048 at some point if I find it's useful.
This is important for a few reasons. First, when forming A-MPDU or AMSDU
aggregates the frame sizes are larger, and thus the TX time calculation
is woefully, increasingly wrong. Secondly, the behaviour of 802.11 channels
isn't some fixed thing, both due to channel conditions and radios themselves.
Notably, there was some observations done a few years ago on 11n chipsets
which noticed longer aggregates showed an increase in failed A-MPDU sub-frame
reception as you got further along in the transmit time. It could be due to
a variety of things - transmitter linearity, channel conditions changing,
frequency/phase drift, etc - but the observation was to potentially form
shorter aggregates to improve BER.
* .. and then modify the ath TX path to report the length of the aggregate sent,
so as the statistics kept would line up with the correct bucket.
* Then on the rate control look-up side - i was also only using the first frame
length for an A-MPDU rate control lookup which isn't good enough here.
So, add a new method that walks the TID software queue for that node to
find out what the likely length of data available is. It isn't ALL of the
data in the queue because we'll only ever send enough data to fit inside the
block-ack window, so limit how many bytes we return to roughly what ath_tx_form_aggr()
would do.
* .. and cache that in the first ath_buf in the aggregate so it and the eventual
AMPDU length can be returned to the rate control code.
* THEN, modify the rate control code to look at them both when deciding which bucket
to attribute the sent frame on. I'm erring on the side of caution and using the
size bucket that the lookup is based on.
Ok, so now the rate lookups and statistics are "more correct". However, MCS rates
are not the same as 11abg rates in that they're not a monotonically incrementing
set of faster rates and you can't assume that just because a given MCS rate fails,
the next higher one wouldn't work better or be a lower average tx time.
So, I had to do a bunch of surgery to the best rate and sample rate math.
This is the bit that's a WIP.
* First, simplify the statistics updates (update_stats()) to do a single pass on
all rates.
* Next, make sure that each rate average tx time is updated based on /its/ failure/success.
Eg if you sent a frame with { MCS15, MCS12, MCS8 } and MCS8 succeeded, MCS15 and MCS
12 would have their average tx time updated for /their/ part of the transmission,
not the whole transmission.
* Next, EWMA wasn't being fully calculated based on the /failures/ in each of the
rate attempts. So, if MCS15, MCS12 failed above but MCS8 didn't, then ensure
that the statistics noted that /all/ subframes failed at those rates, rather than
the eventual set of transmitted/sent frames. This ensures the EWMA /and/ average
TX time are updated correctly.
* When picking a sample rate and initial rate, probe rates aroud the current MCS
but limit it to MCS0..7 /for all spatial streams/, rather than doing crazy things
like hitting MCS7 and then probing MCS8 - MCS8 is basically MCS0 but two spatial
streams. It's a /lot/ slower than MCS7. Also, the reverse is true - if we're at
MCS8 then don't probe MCS7 as part of it, it's not likely to succeed.
* Fix bugs in pick_best_rate() where I was /immediately/ choosing the highest MCS
rate if there weren't any frames yet transmitted. I was defaulting to 25% EWMA and
.. then each comparison would accept the higher rate. Just skip those; sampling
will fill in the details.
So, this seems to work a lot better. It's not perfect; I'm still seeing a lot of
instability around higher MCS rates because there are bursts of loss/retransmissions
that aren't /too/ bad. But i'll keep iterating over this and tidying up my hacks.
Ok, so why this still something I'm poking at? rather than porting minstrel_ht?
ath_rate_sample tries to minimise airtime, not maximise throughput. I have
extended it with an EWMA based on sub-frame success/failures - high MCS rates
that have partially successful receptions still show super short average frame
times, but a /lot/ of retransmits have to happen for that to work.
So for MCS rates I also track this EWMA and ensure that the rates I'm choosing
don't have super crappy packet failures. I don't mind not getting lower
peak throughput versus minstrel_ht; instead I want to see if I can make "minimise
airtime" work well.
Tested:
* AR9380, STA mode
* AR9344, STA mode
* AR9580, STA/AP mode
le oops, trim out an #if 1 that I didn't fully delete.
Cool, so now I know it's about 3 weeks between starting on freebsd coding
and breaking the build again. Queue dunce cap.
Fix logic for determining whether to bump up an MCS rate.
* Fix formatting, cause reasons;
* Put back the "and the chosen rate is within 90% of the current rate" logic;
* Ensure the best rate and the current rate aren't the same; this ...
* ... fixes the packets_since_switch[] tracking to actually conut how many
frames since the rate switched, so now I know how stable stuff is; and
* Ensure that MCS can go up to a higher MCS at this or any other spatial stream.
My previous quick hack attempt was doing > rather than >= so you had to go
to both a higher root MCS rate (0..7) and spatial stream. Eg, you couldn't
go from MCS0 (1ss) to MCS8 (2ss) this way.
The best rate and switching rate logic still have a bunch more work to do
because they're still quite touchy when it comes to average tx time but at least
now it's choosing higher rates correctly when it wants to try a higher rate.
Tested:
* AR9380, STA mode
Limit the tx schedules for A-MPDU ; don't take short retries into account and remove the requirement that the MCS rate is "higher" if we're considering a new rate.
Ok, another fun one.
* In order for reliable non-software retried higher MCS rates, the TX schedules
(inconsistently!) use hard-coded lower rates at the end of the schedule.
Now, hard-coded is a problem because (a) it means that aggregate formation
is limited by the SLOWEST rate, so I never formed large AMDU frames for
3 stream rates, and (b) if the AP disables lower rates as base rates, it
complains about "unknown rix" every frame you transmit at that rate.
So, for now just disable the third and fourth schedule entry for AMPDUs.
Now I'm forming 32k and 64k aggregates for the higher density MCS rates
much more reliably.
It would be much nicer if the rate schedule stuff wasn't fixed but instead
I'd just populate ath_rc_series[] when I fetch the rates. This is all a
holdover of ye olde pre-11n stuff and I really just need to nuke it.
But for now, ye hack.
* The check for "is this MCS rate better" based on MCS itself is just garbage.
It meant things like going MCS0->7 would be fine, and say 0->8->16 is fine,
(as they're equivalent encoding but 1,2,3 spatial streams), BUT it meant
going something like MCS7->11 would fail even though it's likely that
MCS11 would just be better, both for EWMA/BER and throughput.
So for now just use the average tx time. The "right" way for this comparison
would be to compare PHY bitrates rather than MCS / rate indexes, but I'm not
yet there. The bit rates ARE available in the PHY index, but honestly
I have a lot of other cleaning up to here before I think about that.
* Don't include the RTS/CTS retry count (and thus time) into the average tx time
caluation. It just makes temporarily failures make the rate look bad by
QUITE A LOT, as RTS/CTS exchanges are (a) long, and (b) mostly irrelevant
to the actual rate being tried. If we keep hitting RTS/CTS failures then
there's something ELSE wrong on the channel, not our selected rate.
Fix correct status when completing frames with short failures.
My preivous logic was a bit wrong. This caused transmissions that failed due
to a mix of short and long retries to count intermediate rates as OK if the
LONG retry count indicated some retries had made it to this intermediate rate,
but the SHORT retry count was the one that caused the whole transmit to fail.
Now status is passed in again - and this is the status for the whole transmission -
and then update_stats() does some quick math to see if the current transmission
series hit its long retry count or not before updating things as a success
or failure.
Obey the maximum frame length even when using static rates.
I wasn't enforcing the maximum packet length when using static rates
so although the driver was enforcing it itself OK, the statistics were
sometimes going into the wrong bin.
Tested:
* AR9380, STA mode
reset hardware if this particular mac bug is seen.
I have to dig into why I'm seeing it on chips as late as the AR9380 era
stuff (as it's marked as an AR5416 bug, but who knows!) but i'm seeing
aggregate TX frames complete with no blockack bit set. So, everything
should be treated as a failure and do a hardware reset for good measure.
Tested:
* AR9380, STA mode
* AR9580 (5GHz), AP mode
Hopefully recover better-er upon RX restart on AR9380.
This is all very long-standing bug stuff that is touchy and still poorly
documented. Ok, here goes.
The basic bug:
* deleting a VAP causes the RX path (and TX path too) to be restarted
without a full chip reset, which causes RX hangs on the AR9380 and later.
(ie, the ones with the newer DMA engine.)
The basic fix:
* do an RX flush when stopping RX in ath_vap_delete() to match what happens
when RX is stopped elsewhere. This ensures any pending frames are completed
and we restart at the right spot; it also ensures we don't push new RX buffers
into the hardware if we're stopping receive.
The other issues I found:
* Don't bother checking the RX packet ring in the deferred read taskqueue;
that's specifically supposed to be for completing frames rather than
just yanking them off the receive ring.
* Cancel/drain any pending deferred read taskqueue. This isn't done inside
any locks so we should be super careful here. This stops the hardware
being reprogrammed at the same time in another thread/CPU whilst we're
stopping RX.
* .. (yes, this should be better serialised, but that's for another day. maybe.)
* Add more debugging to trace what's going on here.
And the fun bit:
* Reinitialise the RX FIFO ONLY if we've been reset or stopped, rather than just
reset. I noticed that after all the above was done I was STILL seeing RXEOL.
RXEOL isn't enabled on the AR9380 so I'd only see it if I was sending TX frames
(ie a ping where it'd be transmitted but never received) so I was not being
spammed by RXEOL. So, as long as stuff is stopped, restart it.
This seems to be doing the right thing in both AP and STA modes.
What I should do next, if I ever get time:
* as I said above, serialise the receive stop/start to include taskqueues
* monitor RXEOL on the AR9380 and I keep seeing it spammed / lockups, just
go do a full chip reset to get things back on track. It sucks, but it
is better than nothing.
Tested:
* AR9380 AP/STA mode, adding/deleting a hostap VAP to trigger the TX/RX
queue stop/start; whilst also running an iperf through it. Lots of times.
Lots. Of.. Times.
Propagate the HAL_RESET_TYPE through to the chip reset; set it during ath_reset()
Although I added the reset type field to ath_hal_reset() years ago,
I never finished adding it both throughout the HALs and in if_ath.c.
This will eventually deprecate the ath_hal force_full_reset option
because it can be requested at the driver layer.
So:
* Teach ar5416ChipReset() and ar9300_chip_reset() about the HAL type
* Use it in ar5416Reset() and ar9300_reset() when doing a full chip reset
* Extend ath_reset() to include the HAL_RESET_TYPE parameter added in the above functions
* Use HAL_RESET_NORMAL in most calls to ath_reset()
* .. but use HAL_RESET_BBPANIC for the BB panics, and HAL_RESET_FORCE_COLD during fatal, beacon miss and other hardware related hangs.
This should be a glorified no-op outside of actual hardware issues.
I've tested things with ath_hal force_full_reset set to 1 for years now,
so I know that feature and a full reset works (albeit much slower than
a warm reset!) and it does unwedge hardware.
The eventual aim is to use this for all the places where the driver
detects a potential hang as well as if long calibration - ie, noise floor
calibration - fails to complete. That's one of the big hardware related
things that causes station mode operation to hang without easy recovery.
Differential Revision: https://reviews.freebsd.org/D24981
Update ath_rate_sample to use the same base type as ticks.
Until net80211 grows a specific ticks type that matches the system,
manually use the same type as the kernel/net80211 'ticks' type
(signed int.)
Tested:
* AR9380, STA mode
Don't re-program the beacon timers if we miss a beacon in software-beacon STA mode.
This is something I added a few years ago to handle resyncing the beacon if
we miss a beacon or need to sync after association/reassociation/powersave.
However, if we're doing STA+AP mode (eg DWDS) then we don't want
to reprogram the beacons here; this may upset normal AP operation.
I missed checking for the sc->sc_swbmiss flag so I was reinitialising
the beacon timers after every beacon miss / TSFOOR option, and
that isn't likely good.
This plus ensuring that STA's are created with "-beacon" to disable
BMISS/TSFOOR processing will hopefully quieten some of the issues
I've seen with missed beacons / TSFOOR (out of range) interrupts
coming in when operating in STA mode.
Tested:
* AR9380/AR9580, STA+AP modes
Don't update the beacon bits from beacon frames in hostapd mode.
This logic is running the beacon receive bits in STA+AP mode on both the
STA and AP side. The STA side sees its beacons from the BSS fine; the
AP side is seeing other beacons on the same channel but with the BSS
node for some odd reason. (I think it's a valid reason, but I currently
forget what that valid reason is.)
So, just to be cleaner about things, don't run the nexttbtt/etc bits
at all if we're in hostap mode. If I ever get mesh working then maybe
I'll make sure it works right on mesh+ap and mesh+sta modes.
Whilst here, log the VAP i'm being called on to make it clearer what
is going on. I may end up adding a VAP dprintf version of this at
some point.
Tested:
* AR9380, STA (DWDS client) + hostap on the same NIC
Add KeyMiss for AR5212/AR5416 series chips.
This is a flag from the MAC that says the received packet didn't match
a keycache slot. This isn't technically a problem as WEP keys don't
match keycache slots (they're "global" keys), but it could be useful
for tracking down CCMP decryption failures.
Right now it's a no-op - it mirrors what the AR9300 HAL does and it
just increments a counter. But, hey, maybe one day I'll use it for
diagnosing keycache/CCMP decrypt issues.
ath: clean up empty lines in .c and .h files
replace the hard-coded magic values in if_athioctl.h with constant defines
Replace some hard-coded magic values in the ioctl stats struct with
defines. I'm going to follow up with some more sanity checking in
the receive path that also use these values so we don't do bad
things if the hardware is (more) confused.
Don't use hard-coded values in the sanity check.
Don't use hard-coded values in the phy error and receive antenna
checks.
also remove the magic size value here for the transmit antenna statistics.
Change-Id: Ifebebef068d9abe7abfa61204dc900095bd6914c
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3921
Reviewed-by: Adrien Destugues <[email protected]>
* kMaxOptionSize: TCP header size is 60 bytes. process_options() would have
accepted a longer header as permitted. add_options() would have possibly added
more options or SACK entries as permitted.
* tcp_segment: reserve memory for sack entries.
* _SendQueued(): "fLastAcknowledgeSent <= fReceiveNext": also send SACK entries
for received data when acknowledging a missing segment.
* _SendQueue(): after acknowledging, cancel the delayed acknowledgment timer.
* _Receive(): if calling Acknowledged() already triggered sending a segment
including an acknowledgement (piggy-back), remove "immediate acknowledge"
from the action. This helps to reduce empty ACKs for bidirectional streams.
Change-Id: I32808fbe549be0f5b25bcf4be17cd91a640b8ec4
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3906
Reviewed-by: Adrien Destugues <[email protected]>
The ioctl call cannot know the expected number of arguments
because it depends on the specific ioctl being used, and the
same value could be used to do different things by different
devices. Without knowing that, it is not safe to use va_arg
(at best a random value will be read from the stack, at worst,
it will just crash).
This changes the implementation of ioctl in two ways:
- For C++ code: a 4 argument function with default values
for arguments 3 and 4.
- For C code: wrap arguments 3 and 4 in a struct with the
help of a macro, providing something that behaves like the
C++ version.
So, with this new code:
- Calling ioctl with only 3 arguments sets the 4th one to 0
- Calling ioctl with only 2 arguments sets the 3rd and 4th to 0
- Calling with 1 or 5+ arguments is a compile time error
The existing ioctl symbol is preserved for ABI compatibility.
Change-Id: I6d4d1d38fccd8cc9bd94203d3e11aeac6da8efc3
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3360
Reviewed-by: Adrien Destugues <[email protected]>
this adds kernel & libroot stack protector hooks. it uses /dev/random in userspace.
A configure option --enable-stack-protector is added to activate -fstack-protector
on selected system components (ATM apps, kits, servers).
Change-Id: If3a2920ba9aa0a85eaff4ba6778947f8c76ade31
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3895
Reviewed-by: Adrien Destugues <[email protected]>
a protection_max attribute is added in VMArea.
a read-only opened file already can't be mapped shared read-write at the moment,
but can later be changed to read-write with mprotect() or set_area_protection().
When creating the VMArea, the actual maximum protection is stored in the area,
so that it can be checked when needed.
this fixes a VM TODO.
Change-Id: I33b144c192034eeb059f1dede5dbef5af947280d
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3804
Reviewed-by: Adrien Destugues <[email protected]>
UnixEndpoint::Receivable(): EOF means there is nothing left to read, and
the shutdown happened on the read side or the write side.
also fix x86_64 build with trace
Change-Id: I54c806f0b900591c3d441240b8f6768dfb756bad
Reviewed-on: https://review.haiku-os.org/c/haiku/+/3808
Reviewed-by: Adrien Destugues <[email protected]>
Jérôme Duval